• 1.800.860.6272
  • Shopping Cart

    There are 0 items in your cart.

    You have no items in your shopping cart.

    Cart Subtotal: $0.00

    Home / Science projects / Marble Paper Science Project: Two Methods
    • Marble Paper Science Project: Two Methods

      Marble Paper Science Project: Two Methods

      Marbled Paper Project #1

      Paper marbling sprawls continents and centuries and relies on a variety of techniques to produce its stone-like or curlicue effects. We'll explore two different marbling techniques, and once you understand the basics of paper marbling, you can experiment to find the method you like best. Then use your marbled paper for cards, gift wrap, or stick it in a frame for one-of-a-kind art!

      What You Need:

      • Plain non-glossy white paper
      • Cornstarch
      • Water
      • Fork
      • 600 ml beaker
      • Paint brush
      • Alum
      • Food coloring or acrylic paints
      • Medicine dropper or pipet (if using acrylic paints)
      • Large shallow pan
      • Toothpick, comb, fork, chop sticks, paint brushes, or the like
      • Newspaper
      • Iron (optional)

      What You Do:

      1. Use the fork to mix 1 tablespoon (15 g) of alum into 2 cups (~475 ml) of warm water in the 600 ml beaker until it's completely dissolved. Clean the fork and beaker and set aside.
      2. Make a small mark on one side of the paper with a pencil. Use the brush to lightly coat the marked side of the paper with the alum solution.
      3. Allow the paper to fully dry (about an hour). If the paper is more wrinkled than you'd like, have an adult help you iron it between two plain sheets of paper on the low setting.
      4. Create a size by combining 1/4 cup (2 oz) cornstarch with 1/4 (~60 ml) cup cold water in the 600 ml beaker. Stir with the fork. Once it's well mixed, add 2 cups (~475 ml) cups hot water. Mix until the solution is syrupy and pour in the shallow pan.
      5. Next, drop the food coloring into the size. Use 1-4 colors. If you're using acrylic paint, thin it out with water first, so it's the consistency of milk and use a dropper to put it onto the solution. Alternatively, you can try dipping a brush into the paint and gently tapping the handle over the solution. You want the paint to float on the surface of the cornstarch solution.
      6. Use the comb, chopsticks, etc., to swirl, rake, and otherwise distribute the paint across the solution's surface. Avoid disrupting it so much that the individual colors are no longer visible.
      7. Carefully lay the paper, marked side down, into the size, smoothing it out so that no bubbles remain. Leave it for 30 seconds or so.
      8. Lift the paper from the solution and rinse off any excess size with a gentle stream of water. Repeat step 3.
      9. Place a sheet of newspaper in the solution to absorb any excess paint, and repeat steps 5-8.

      What Happened:

      First, you prepared the paper with a mordant, a substance used to set dyes. Mordants are used to set dye on fabrics and paper and to augment staining of cell and tissue samples. Since we used the mordant before the dying process, it's called pre-mordanting or onchrome. Meta-mordanting, or metachrome, means the mordant is included in the dye, and post-mordanting, or after-chrome, is when mordant is applied following the dying process.

      Once the mordanted paper was dry, you transferred a paint design from a viscous solution's surface to the paper. You did this by making a size, or a substance used to alter the way the paper interacts with liquids. Specifically, the size slows the paper's absorption rate, allowing the paint to adhere to the paper's surface rather than being absorbed. Since the size has higher density than the paint, the design you made sits atop the size. Can you think of other materials you could use to make a size?

      Tips: If your water stream isn't gentle enough, it will wash off some of your paint, too!
      A common mistake is layering the paint too thick atop the size; a little goes a long way.
      Try making the classic nonpareil pattern by first raking the length of your size container, then carefully raking the width.

      Marbled Paper Project #2

      Another less-precise paper-marbling method uses shaving cream as the size. Here's how.

      1. Dispense a mound of shaving cream in a shallow pan.
      2. Level it out with a ruler or spatula as best you can.
      3. Drop food coloring or paint onto the shaving cream and swirl it (as above. Take care not to mix the colors too much.
      4. Carefully press the paper into the shaving cream, smoothing out bubbles. Leave it on for a minute or so.
      5. Lift the paper off. Gently rinse under running water and let dry.
      6. As above, have an adult help you iron it between two clean sheets of paper, if you wish.

    « Previous Article: Frosted Window Panes Science Project

    Next Article: Foamy Flask | Elephant Toothpaste Project »

    « Previous Article: What is a Life Cycle?

    Next Article: Learn About Acids & Bases »

    Comments




    By: Linde Clark
    Date: Mar 16, 2017

    I used corn starch to size my water, and it fell to the bottom of the pan. I used warm water to thorough dilute and liquify the corn starch. The acrylic paint/ink did not create the effects as the instructions imply. it also fell to the bottom, it did not float like the videos show?????


    By: Janet
    Date: Sep 28, 2015

    It’s great to have these thorough and informative instructions. Because alum is sold in the grocery store, people mistakenly assume it is a non-toxic, harmless substance.  It is aluminum-derived, and especially when addressing children, it should be made very clear that alum is a chemical and should be handled with the kind of precautionary care you would use with anything of that nature: gloves, mask, etc.  Breathing the powder or absorbing the solution through the skin can lead to accumulation of aluminum in the bloodstream.