• 1.800.860.6272
  • Shopping Cart

    There are 0 items in your cart.

    You have no items in your shopping cart.

    Cart Subtotal: $0.00

    Home / Science projects / Balloon Rocket Car + Video
    • Balloon Rocket Car + Video

      Balloon Rocket Car + Video

      A rocket is simply a chamber filled with pressurized gas. A small opening called a nozzle allows the air to escape, causing thrust that propels the rocket. You can demonstrate this when you blow up a balloon and let it go without tying it off. The balloon will fly through the air as all the air inside escapes.

      Pin It

      Sir Isaac Newton laid the foundation for the modern science of rocketry near the end of the 17th century. Newton's Laws of Motion are essential to rocket flight. Here are two of them:


      related product

      Build your own air-powered racer with this convenient kit!

      OWI Air Power Racer Vehicle Kit >>



      1. 'Objects at rest will stay at rest and objects in motion will stay in motion in a straight line unless acted upon by an unbalanced force.' In other words, the forces pushing a rocket up must be stronger than the force of gravity pulling it down.

      2. 'For every action there is always an opposite and equal reaction.' When an action takes place, like gases escaping from the rocket, a reaction follows - the rocket rises in the air.

      The principles of rocketry apply to more than flying rockets - with this project you can make a 'rocket car' that is powered by pressurized gas (air in a balloon!). Adult supervision recommended.

      >> Watch our video to see the car in action!

      What You Need:

      • 16-20 oz. plastic water bottle
      • Drinking straws
      • Wooden shish-kabob skewers
      • 4 plastic bottle caps
      • Balloon
      • Duct tape or masking tape
      • Nail, hammer, knife, scissors

      What You Do:

      The water bottle forms the chassis, or body, of your balloon car. You can start by mounting the wheels on this body.

      1. Cut a drinking straw into two pieces as long as the water bottle is wide. Use strips of tape to attach them to the bottle - one near the front and one near the back. The axles for the wheels will run through these straws, so line them up carefully so the wheels won't be crooked.

      2. Use a hammer and a small nail to poke holes through the center of four bottle caps. Cut two pieces of a wooden skewer about an inch-and-a-half longer than the pieces of straw you taped to the bottle. Push one end of each skewer through the hole in the center of a bottle cap. If the cap doesn't fit snugly on the skewer, use some modeling clay to hold it in place. Next, thread the skewers through the straws on the bottle and attach the other wheels to the other ends. Make sure your car rolls smoothly.

      3. Stretch out a large balloon by blowing it up and then letting the air out of it a few times. Next, make a nozzle. The size of the nozzle is very important. If it is too small, the air can't escape with enough force to propel the car forward. If it is too big, the air will escape too fast and the car won't go very far. Create the nozzle by taping four drinking straws together. Insert the straws into the mouth of the balloon and seal the opening by wrapping a strip of duct tape around it several times.

      4. To mount the balloon/nozzle on the car, use a knife to cut two perpendicular slits (to make an X) in the top of the car about 4' back from the mouth of the bottle. Thread the nozzle through this opening and out through the mouth of the bottle. Leave about an inch of the nozzle sticking out of the mouth.

      5. Find a hard surface, like a long table, linoleum floor, or sidewalk. Blow up the balloon through the straws at the mouth of the bottle. Pinch the base of the balloon to prevent the air from escaping too soon. Set the car down, let go of the balloon, and watch it go!

      The air in the balloon is gas under pressure. The air pushes against the balloon, causing it to expand, but the balloon is also pushing back on the air. The pressure of the balloon pushes the air right out through the nozzle, which creates thrust that propels the car forward.

      Keep track of how long the car rolls and how far it goes. Try it several times, then try changing the design to see if you can get it to go farther or faster. How will it work if you only use three straws for the nozzle? What if you use a bigger or smaller balloon? Does the car go farther on linoleum or the sidewalk? Why do you think this might be? Will the car go farther if you start it at the top of a ramp?

      Decorate your car and have races with siblings or friends. Try to figure out why one car goes faster or farther than another, and keep experimenting to make your design better!

    « Previous Article: Electromagnetism Experiments

    Next Article: Make a Cartesian Diver »

    « Previous Article: Storms

    Next Article: Ocean Animals Worksheet »


    By: anaya/jada
    Date: Jan 13, 2016

    me and my friend jada are making a balloon car for our science project. I think that this is a great rocket car and it goes really fast. That is what we need for the competition and we are looking forwards to or results. Although i have a question. Is there any way to customize this car so that it will be pretty.

    By: SC
    Date: Jan 06, 2016

    good description of how air can be used to propel an object forward. we will do this soon.

    By: Shahid Hanif Bhatbharde
    Date: Nov 27, 2015

    I like this vedio so much.
    Good job.It is awesome car.
    I also makes this ballon car.
    It is very speedy race car.
    It runs anywhere in the house.
    My mom and dad like this car so much.
    I gifted this car in my sister’s birthday.
    Thank you very much.
    Comment written by HAH.

    By: Gwen
    Date: Nov 18, 2015

    good job ( i guess )

    By: Georgia
    Date: Oct 16, 2015

    Can it carry a 200g weight??? It’s for a physics assignment and that is the only guideline.

    By: Gene
    Date: Oct 02, 2015

    Good project

    By: Pria
    Date: Sep 28, 2015

    This is sweet I used on project and helped me a ton

    By: jakayla
    Date: Sep 23, 2015

    the best project ever, it’s so awesome.

    By: Pravin
    Date: Sep 11, 2015

    Good job, v-good

    By: Manoj
    Date: Jun 12, 2015

    very nice balloon rocket car